NS0-182 Online Practice Questions and Answers

You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are

associated with this port are migrated to a port that is not expected.

In this scenario, what would cause this behavior?

A. The network port is configured incorrectly.

B. The broadcast domain is configured incorrectly.

C. There are no online ports within the same failover group.

D. The network failover port is not licensed.

What are two types of load balancing methods available in multimode interface groups? (Choose two.)

A. broadcast domain-based load balancing

B. IP-based load balancing

C. LIF-based load balancing

D. port-based load balancing

A node joins a cluster in ONTAP 9.5.

Which statement is correct about the NTP configuration in this situation?

A. A node that joins a cluster must reboot before running the NTP service.

B. A node that join a cluster has a separate NTP service.

C. A node that joins a cluster must be manually configured for NTP.

D. A node that joins a cluster automatically adopts the NTP configuration of the cluster

During handover, a customer asks you how to obtain support from NetApp after installation.

What are two responses in this scenario? (Choose two.)

A. Visit.

B. Visit mysupport.netapp.com

C. Send an AutoSupport message from the system.

D. Contact Global Support by telephone.

You create a LIF called svm_cifs_lif01 on a port that is already in an up state. After you test the storage failover, the LIF does not automatically revert to its home port.

In this scenario, what should you do to solve the problem?

A. Configure a new failover group.

B. Configure the LIF with the DHCP option.

C. Add the port in a broadcast domain.

D. Configure the LIF with the automatic revert option.

A customer has an ONTAP 9.5 8-node FAS8080 EX cluster. The cluster uses CN1610 cluster interconnect switches. The current workload runs NAS protocols. A business unit wants to add an additional workload that requires expanding the cluster by six AFF A300 nodes and use SAN protocols.

How would you advise the customer in this situation?

A. The customer must upgrade the existing cluster interconnect switches, add the six new nodes, and execute the new SAN workload within a new SVM only.

B. The customer should create a new cluster with the new AFF A300 nodes for the SAN workload.

C. The customer must upgrade the existing cluster interconnect switches, add the six new nodes, and execute the new SAN workload within an existing SVM.

D. The customer can add the six new nodes to the existing cluster interconnect switches and execute the new SAN workload within an existing SVM.

Select the Exhibit tab.

You install a new FAS2552 HA using a DS2246 disk shelf and ONTAP 9.5 on a customer site.

Referring to the exhibit, which two statements describe what is required to get an HA cabled system? (Choose two.)

A. Insert a cable from right controller port 0a to the IOMB square, and from port 0b to the IOMA square, then cable in-band ACP.

B. Insert a cable from right controller port 0a to the IOMB square, and from port 0b to the IOMA circle.

C. Insert a cable from left controller port 0a to the IOMA circle, and from port 0b to the IOMB circle, the cable in-band ACP.

D. Insert a cable from left controller port 0a to the IOMA square, and from port 0b to the IOMB circle.

A customer buys a new switchless ONTAP 9.5 FAS2650 cluster. You are asked to install the system at the customer's site.

Which three steps are needed to accomplish this task? (Choose three.)

A. Cable the ACP.

B. Cable the cluster-interconnect to the CN1610 switches.

C. Connect both power cords.

D. Install the system in the rack.

E. Cable the controller for switchless ONTAP software.

You are setting up a new cluster. The customer notices that there are many management ports on the

cluster. The customer wants to know the purpose of the cluster management LIF.

In this situation, what should you tell the customer?

A. The cluster management LIF provides a dedicated IP address for the entire cluster and can fail over to any port in the cluster that is available in the broadcast domain.

B. The cluster management LIF provides a dedicated IP address for managing a particular node in the cluster and is used for system maintenance.

C. The cluster management LIF is used to carry intracluster traffic between nodes in a cluster and must be created on a 10GbE network port.

D. The cluster management LIF provides multiple IP addresses for the entire cluster and can fail over to any cluster or intercluster ports.

A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves.

What would you advise the customer in this scenario?

A. Convert the ACP communication from out-of-band to in-band channel.

B. Remove the ACP cabling from the stack before adding the new shelves.

C. Remove the DS4243 shelves, but you must add the new DS4246 shelves to a new stack.

D. Configure the shelf IDs of the new DS4246 shelves to match the existing DS4246 shelves.

You have just replaced a FAS controller with a new controller and installed the appropriate licenses for the new FAS controller.

What are two ways to remove unused licenses in this situation? (Choose two.)

A. Use OnCommand Unified Manager.

B. Use OnCommand System Manager.

C. Use the cluster license clean-up nused command.

D. Use the system license clean-up nused command.

A customer wants to expand their 10-node AFF A700s SAN cluster on Cisco Nexus 3132Q-V interconnect switches. The customer has six AFF A700s nodes available.

In this scenario, what should you do to expand the cluster?

A. Add two nodes to the existing cluster without exceeding the SAN cluster limit.

B. Add six nodes to the existing cluster.

C. Replace the switches with Cisco Nexus 5596T switches and then add the six nodes.

D. Add an expansion module to each switch and then add the six nodes.

A customer has recently purchase a new ONTAP 9.0 storage system and wants you to join the nodes to an existing cluster running ONTAP 9.5.

What is the first step for adding the new controllers to the existing cluster?

A. You must ensure that all network switches are upgraded and online.

B. You must configure the existing cluster to accept the Joining nodes.

C. You must make sure that there Is the same amount of disk shelves attached to all nodes.

D. You must match the operating system.

You are using a NetApp CN1610 cluster-interconnect switch and need to connect a new AFF A800A node to the switch.

In this scenario, how many Ethernet ports per node are required on each switch?

A. 2

B. 4

C. 6

D. 1

You have just added a new DS4246 shelf with 24 x 10 TB SATA HDDs to a single FAS2650 node as the

first SATA shelf. You must keep two SATA spare disks on the shelf.

What is the maximum number of SATA data disks available in this scenario?

A. 19

B. 16

C. 22

D. 20