ISS-003 Online Practice Questions and Answers

Which of the following BIOS setup pages should be entered in an Intel Server to configure the onboard SATA mode?

A. Advanced PCH configuration

B. Advanced-Processor Configuration

C. Advanced-Disk Configuration

D. Advanced-PCI Configuration

E. Advanced-Mass Storage Controller Configuration

Your customer calls to say that an Intel Server system R1208WT2GS is showing several entries in the system event log that PSU redundancy was lost. How would you advise your customer from the following list?

A. Only one CPU is installed

B. ThePSUsare pluggedinto differentphases

C. Redundancy should be enabled in BIOS

D. An unsupported UPS is being used

E. The PSUs have different wattages

Your customer is buying a new server and due to space constraints it needs to enable maximum storage as well. The minimum acceptable number of drives is at least 20 HDDs so that secure arrays may be created. Please choose your answer from the list below:

A. Intel Compute Module HNS2600TPand; Intel Server Chassis H2216XXKR2

B. Intel Server System R1304WTXXX

C. Intel Server System R2224WTTYS

D. Intel Server System R1208WTXXX

Your customer is in the market to upgrade their infrastructure. A key requirement is the number of add-in components that each server can support. Please advise your customer which systems have the largest number of PCIe expansion slots. (Select ALL that apply).

A. Intel Server Board S2600CWT

B. Intel Compute Module HNS2600KP

C. Intel Server System R2224WTTYS

D. Intel Server System R2208WTTYS

E. Intel Compute Module HNS2600TP

F. Intel Server Board S2600CW2

G. Intel Server System R2208WT2YS

H. Intel Compute Module HNS2600KPF

Which of the following features of IPMI, are built-in on Intel Server Boards? (Select ALL that apply).

A. Monitoring of fan speeds

B. Remote keyboard video, mouse, and media redirection

C. Remote alerting via PET traps

D. System event log

E. Increased processor speed

F. Built-in web server

A customer is not able to enter the RAID BIOS setup utility for an onboard controller. Which of the following troubleshooting steps should an Intel Server Specialist take when trying to resolve the customer's issue?

a.

Disable quiet boot.

b.

Check mhether the RAID 5 actvaton key is installed.

c.

Make sure the customer is only using SATA drives.

d.

Update the system BIOS to the latest version.

e.

Check the mass storage controller mode in BIOS setup.

f.

Verif y the HSBPA cable is connected.

g.

Verif y the SGPIO cable is connected.

h.

Verif y there are disks connected to the motherboard.

A.

b,e,h

B.

a,e,h

C.

c,d,e

D.

a,e,f

When installing an Intel Raid Web Console 2 on Microsoft Windows 2012 R2, how is the username and password set?

A. Edit a file in the program files folder for RAID Web Console 2.

B. No need to set username and password, Intel Raid Web Console 2 uses the OS administrator credentials.

C. Enter the desired username and password in the wizard interface during installation.

D. No need to set username and password, Intel Raid Web Console 2 uses the BMC administrator credentials.

Your customer is looking for a Server System which will support two high-end GPGPU cards. As the Intel Server Specialist which of the following server systems would you recommend? (Select ALL that apply).

A. Intel Server System P4308RPLSHDR

B. Intel Server System H2216XXKR2 and HNS2600KP

C. Intel Server System P4304CR2LFKN

D. Intel Server System P4308RPLSHDR

E. Intel Server Chassis P4304XXMUXX and board S2600CW2

Your customer is undertaking a complete infrastructure renewal for one of their bigger customers, and has been asked to pay attention to both power and efficiency. Please explain from all the different power supplies that are available for Intel Server systems; which PSUs are compatible with systems based on the Intel Server board S2600WT. Please choose from the list below. (Select ALL that apply).

A. 460W

B. 650W

C. 750W

D. 860W

E. 1100W

F. 1200W

G. 1600W

While installing MS Windows 2012 R2 on a RAID array created on an Intel RAID controller RS3MC044 the array cannot be found. How would you proceed from the list below?

A. The Drives are not marked online

B. The Virtual Drive was not initialized

C. The Virtual Drive is not set as bootable

D. A driver is required

E. The Intel RAID controller is not the first boot device

Your customer wishes to set up a pilot system with a 1U, small form factor, managed server, destined for a small datacenter, with a maximum CPU draw of 95w TDP; before placing his main order for 50 systems. Two of the major requirements are 1) for the system to send out an alert email as well as an audible alert if a single drive fails in the software based RAID 1 array and 2) to enable remote monitoring of the system. Which of the following configuration choices would you recommend? (Select ALL that apply).

A. Intel ESRT2 RAID 1 configured with email alerting

B. Remote Intel Management Module RIMM 4

C. AXXRMM4LITE

D. Intel Xeon?E3-based server system

E. Remote Web Console 2

F. Matrix RAID 1

G. Intel RAIDMatrix 2.5

H. Intel RAIDsoft 3

I. Configure BMC for email alerting

A reseller would like to obtain detailed information on an Intel® C610 Chipset based server that does not have an operating system installed, which of the following options are available? (Select ALL that apply).

A. The FRUSDR utility can be run from the EFI shell.

B. The utility "sysinfo" can be run and all the relevant information will be saved to a text file on the local USB key.

C. The server can be booted to the EFI environment and syscfg can be run.

D. If BMC IP address and users are configured correctly, the information can be cut and pasted from the web view of the server configuration detail.

E. The command SELVIEW 一 Sensors /ALL will output a file that shows all system settings available.

F. ME can be used to save the information on the specific server.

An Intel® Server Specialist is helping a customer configure their RAID using the Intel® RAID Web Console. The Specialist advises the customer to use Auto-Configuration Mode as it automatically creates the best possible RAID-configuration for the available hardware. Which of the following configurations are NOT supported using this mode? (Select ALL that apply).

A. Auto Configuration cannot be used when using more than one backplane.

B. Auto Configuration cannot be used with SSD drives.

C. Auto Configuration cannot be used for RAID 10, 50, or 60.

D. Auto Configuration cannot be used for creating RAID on 2 HDDs.

E. Auto Configuration cannot be used with mixed SATA and SAS drives.

During a training event that you are giving as an Intel® Server Specialist on the use of RAID in protecting customer data from loss, you are asked to explain how a RAID array can be configured without using the operating system. How would you answer this question from the list below? (Select ALL that apply).

A. You can use the System Configuration Utility in UEFI

B. You can use the RAID BIOS

C. You can use the RAID web console

D. You can use SysInfo in UEFI

E. You can use the CmdTool2

Your customer has spent a long time installing a new RAID Card and is asking you the Intel® Server Specialist 一 why they see more than one controller listed when logging on to RAID Web Console 2 to configure their single card. Which of the following is correct?

A. Software RAID is more robust than Hardware RAID, so is the default in RWC2.

B. Hardware RAID is more robust than Software RAID, but the Software option is offered as a backup to the hardware option in RWC.

C. The new RWC2 is enabled for all RAID controllers including software RAID like ESRT2. If this has been enabled in BIOS it will be visible to RWC2.

D. Software RAID takes precedence over Hardware RAID, so this will always be visible.