Certbus > HP > HP ATP > HP2-T26 > HP2-T26 Online Practice Questions and Answers

HP2-T26 Online Practice Questions and Answers

Questions 4

What should a support engineer use to perform a firmware update to a c-Class PCI Expansion Blade?

A. OA CLI

B. HP SmartStart

C. Firmware Maintenance DVD

D. OA GUI

Browse 268 Q&As
Questions 5

You are doing troubleshooting and need to access a single server blade console. Which configuration option is the best to use?

A. Connect an SUV to the KVM module.

B. Enable the iLO Advanced license in RBSU.

C. Enable graphics mezzanine support.

D. Connect an SUV cable to the blade.

Browse 268 Q&As
Questions 6

A customer is installing a new drive in a BL460c Gen8. None of the LEDs on the drive are lit. What is a possible cause?

A. The customer used a third party drive.

B. Dynamic Power Saving disables LEDs.

C. The backplane port is disabled in system ROM.

D. There is no activity on the drive.

Browse 268 Q&As
Questions 7

Which step must be done after the system board is replaced on a BL460C G6?

A. Re-enter the serial number.

B. Clear NVRAM.

C. Enable ASR.

D. Reconfigure array.

Browse 268 Q&As
Questions 8

Which resource can be used to identify the warranty status of an HP BL460c G6 Server Blade?

A. IT Resource Center

B. HP Service Advisory

C. HP Onboard Administrator

D. HP Service Dashboard

Browse 268 Q&As
Questions 9

Your customer used RAID 1+0, lost two drives, and the array failed. What can you recommend to better address the need for any two drive failures at the same time?

A. RAID 1

B. RAID 5

C. RAID 6

D. RAID 10

Browse 268 Q&As
Questions 10

How many power supplies are needed for an (N+N) configuration in a c7000 enclosure?

A. 3

B. 4

C. 5

D. 7

Browse 268 Q&As
Questions 11

What is the correct UEFI shell command to display a list of drivers on an HP Integrity BL860c i2 Server Blade?

A. drivers

B. map

C. drvdiag

D. drvcfg

Browse 268 Q&As
Questions 12

In RBSU, which profile setting takes precedence over the NIC Personality option in a G7 server?

A. ICSI

B. network server mode

C. virtual connect

D. embedded NIC

E. FCoE

Browse 268 Q&As
Questions 13

A customer wants a basic power configuration for a c7000 enclosure using only single-phase power. Which power supply slots in the enclosure must be populated to meet the requirement for N+1 redundancy?

A. 1 and 3

B. 1 and 2

C. 1 and 6

D. 1 and 4

Browse 268 Q&As
Questions 14

Which full-height device bays are in Zone 3 of a c7000 enclosure?

A. 1 and 2

B. 3 and 4

C. 5 and 6

D. 7 and 8

Browse 268 Q&As
Questions 15

Which interface can be used to check the firmware version of all components in a blade enclosure?

A. HP System Update Manager

B. Virtual Connect Manager

C. Onboard Administrator

D. HP System Management Homepage

Browse 268 Q&As
Questions 16

What do you use to access RBSU to retrieve information?

A. F2

B. F8

C. F9

D. F12

Browse 268 Q&As
Questions 17

You have a c7000 with an SB40 Storage Blade installed. It has both SAS and SATA drives. Which statement is true about this configuration?

A. It is not supported. You cannot mix drive types in the same storage blade.

B. It is supported if the drive types are configured in different logical partitions.

C. It is supported. The ACU is able to configure all drives in the same logical partition.

D. It is supported if the drives are the same size.

Browse 268 Q&As
Questions 18

An HP ProCurve 6120G/XG Ethernet Blade Switch has a blinking amber LED for 10/100/1000 port 1. What does this indicate?

A. network link fault

B. link activity at 1 Gb/s

C. prefailure warning

D. switch failure

Browse 268 Q&As
Exam Code: HP2-T26
Exam Name: Servicing HP BladeSystem Solutions
Last Update: Mar 19, 2025
Questions: 268 Q&As

PDF

$49.99

VCE

$55.99

PDF + VCE

$65.99