C4040-129 Online Practice Questions and Answers

A customer is upgrading an HMC to a new release using Recovery DVD5 for the new release level. Which action must be completed before performing the upgrade from DVD process?

A. Run the `HMC Management> Back Up HMC Data' to DVD.

B. Run the `HMC Management> Save Upgrade Data' to HMC disk.

C. Run the `HMC Management> Back Up HMC Data' to NFS server.

D. Run the `HMC Management> Save Upgrade Data' to the administrator's PC.

Consider the following graphic. Where in System i Navigator Management Central are the message monitors configured?

A. Message

B. Commands

C. Extreme Support

D. Collection Services

An administrator needs to upgrade users' IBM i Access for Windows emulators to use Secure Sockets Layer (SSL) protocol. The administrator used the Microsoft Windows administrator account to complete a successful upgrade and subsequent test. After re-booting the Windows PC, users log in using their ID. When users launch the IBM i Access emulator and log into the IBM i server, the emulator session is not SSL secured, even after the successful installation. What is most likely cause of the problem?

A. The Windows client IP address is being blocked by the exit point QIBM_SSL_DEVINIT.

B. The IBM i Access for Windows emulator shortcut for users' desktops were not configured for SSL.

C. The IBM i Access for Windows emulator supports SSL only when run from a Windows administrator account.

D. The Windows client has been assigned a new IP address from the DHCP server which is not registered with the System i SSL server.

An administrator has prepared an update package containing the prescribed groups and HIPER PTF5. When testing the package, a message is received stating some of the PTEs cannot be applied because others are missing.

What is the most efficient approach to accomplish a successful test?

A. Apply the latest technology refresh.

B. Apply the latest cumulative fix package.

C. Inspect the job log for the missing PTFs.

D. Read the PSP for cumulative updates for missing PTFs.

What is the correct command to save objects which are stored in the root file system?

A. SAV

B. SAVES

C. SAVDLO

D. SAVOBJ

A small IBM i partition has batch jobs in subsystem QBATCH that occasionally have very high CPU usage (more than 50%), impacting system performance.

The administrator needs to be able to observe these jobs on a 5250 session when they occur.

Which steps should the administrator take to display the jobs when they occur?

A. WRKACTJOB SBS(QBATCH) CPUPCTLMT(50) INTER VAL(10) and press E19 for auto refresh.

B. WRKSYSACT SBS(QBATCH), enter 50 in the CPU Filter field1 and press F19 for auto refresh.

C. WRKSYSACT, P20 to subset, include QBATCH, set the CPU Filter to 50% and press PIO for auto refresh.

D. WRKACTJOB, press P20 to subset, enter 50% for the CPU, use P16 to sequence by subsystem and press P19 for auto refresh.

Which command is used to turn off the front panel attention light for an IBM i partition?

A. WRKPRB (Work Problem)

B. STRSST (Start System Service Tools)

C. RSTATNIND (Reset Attention Indicator)

D. DSPMSG QSYSOPR (Display Messages on QSYSOPR message queue)

After resetting the QSECQER DST/SST password to the default value1 the password is expired and the administrator is unable to change it from the operating system due to security restrictions. How can the password be changed with the least interruption to other users and jobs on the system?

A. IPL the partition in manual mode, change the QSECOFR DST/SST password.

B. Issue a control panel function 21 to activate DST and change the password there.

C. Issue the command CHGDSTPWD again, but also special password expiration override.

D. Use the serial interface and ASMI Admin profile to enable the QSECOFR profile for DST/SST.

An administrator has successfully used a CL program to perform the nightly backup to an LTO-3 drive defined as TAPO3. A fibre attached LTO-5 drive was added later and it was configured as TAPO4 with resource name TAPO4.

After updating the CL source to reflect this change, the backup is still attempting to run on the LTO-3 drive. Which action is most likely to solve the problem?

A. Recompile the backup program.

B. Change the resource type of TAP04 to LTO-5.

C. Use TAPMLBU4 as fibre attached drives are only supported in library mode

D. Vary off the LTO-3 drive so the program can find the LTO-5 drive

An administrator needs to add a connection to System i Navigator to make it available for monitors, messages, and system activity. Where should the administrator configure this?

A. Systems with partitions > Add System

B. Endpoint systems> New End Point System

C. My Connections > Connection to Systems> Add connection

D. Endpoint systems> New End Point System > Discover Systems

A customer is unable to order PTEs or send service requests to IBM. Which command will enable connections to IBM?

A. CRTSRVCFG ROLE(*PRIMARY)

B. STRSRVAGTTYPE(*ACTIVATE)

C. SNDSRVRQS ACTION(*CONEIGURE) ROLE(*PRIMARY)

D. SNDPTEORD PTEID(*ESERV) ESERV(*PRIMARY) INIT(*YES)

A customer selected option 21 from the SAVE menu, entered their tape library TAPMLBO1 and selected to start the backup immediately. They receive the message "*MOUNTED not correct." What should the administrator do before restarting the save?

A. Use SETTAPOGY to the desired tape category.

B. In WRKMLBSTS allocate the tape drive resource.

C. Initialize the tape to correctly match the cartridge ID.

D. Assure that at least two tapes are ready and initialized in the library.

A POWER7 customer using disk adapters with RAID-5 and hot spare has noticed sudden and significant performance problems with an LPAR. WRKDSKSTS followed by Fl 1 shows the disk units as "DEGRADED". The customer has

attempted to check the RAID card battery in Service Tools but it is not listed.

What is the cause of the degraded status?

A. One of the power supplies in the disk drawer has failed.

B. The cache battery is in the 90-day replacement warning state.

C. The pairing of the RAID cards is broken, so the RAID cache is not in use.

D. The hot spare has taken over for a failed drive and is awaiting replacement.

An administrator needs to set up and configure a monitor for disk usage under Management Central. Monitors, Based on the image shown, which option is used to set up this monitor?

A. Job

B. File

C. System

D. Message

Which command shows CPU utilization for both user jobs and IBM i system tasks?

A. WRKSYSSTS

B. WRKSYSACT

C. WRKTSKSTS

D. WRKACTJOB