300-625 Online Practice Questions and Answers

DRAG DROP

Drag and drop the DCNM configuration tasks from the left onto the correct tools on the right.

Select and Place:

Which result occurs if a device alias is renamed and then the original device alias name is used in an add command in the same session?

A. Both commands execute successfully.

B. The device alias is renamed and the add command is moved to the rejected list.

C. Both commands are moved to the rejected list.

D. The rename command is moved to the rejected list and the add command executes successfully.

Which result occurs when a VSAN is deleted that contains non-trunking ports?

A. The ports are moved to VSAN 4094.

B. The ports are moved to VSAN 1.

C. The ports are removed from the configuration.

D. The port configurations are cleared.

A storage network engineer is implementing a port channel for multiple FCIP interfaces with write acceleration in a client's storage network. Which channel mode must be used?

A. on

B. passive

C. active

D. force

A storage administrator wants to enable NPV in a Fibre Channel edge switch. Which configuration is supported in this mode?

A. Cisco Fabric Services distribution over Fibre Channel

B. E Port connectivity to the core switch

C. local switching of east-west traffic

D. Dynamic Port VSAN Membership

Which configuration is always required when running the setup utility on a Cisco MDS 9000 Series Switch?

A. administrator password

B. management IP address

C. active NTP server

D. active default gateway

Which port mode is used on an NPV device to connect to an NPIV core switch?

A. E

B. F

C. N

D. NP

Which EtherType is used by the FCoE Initialization Protocol?

A. 0x8913

B. 0x8914

C. 0xxfc0e

D. 0x8906

A storage network engineer must install and configure a new MDS switch in a data center network. Which two statements about available choices during the MDS switch initial setup are correct? (Choose two.)

A. The engineer can choose what will be the administrator account.

B. The secure password standard is required.

C. The engineer can configure the default zone policy.

D. The engineer can configure the default switch port trunk mode.

E. The engineer does not have the choice to enable or disable full zoneset distribution.

Which benefit of upgrading to the Cisco DCNM server-based advanced feature license for a Cisco MDS switch is correct?

A. The license can be reassigned when a switch is replaced with a newer version within the same product family.

B. The license can be assigned to either server MAC address or switch serial number.

C. An unlimited number of devices can be added to the list of licensed devices.

D. The license can be reassigned when the switch is replaced with a Cisco Nexus switch.

What does an unlicensed DCNM SAN fail to display?

A. Fibre Channel, FCoE, and iSCSI topologies

B. events and fault management

C. historical performance monitoring

D. real-time performance monitoring

Refer to the exhibit.

The san-user must configure FSPF on the VSAN 500, but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?

A. MDS-A(config)# role name sangroup MDS-A(config-role)# no rule 2

B. MDS-A(config)# role name sangroup MDS-A(config-role)# rule 4 permit config feature fspf

C. MDS-A(config)# role name sangroup MDS-A(config-role)# rule 2 permit config feature vsan

D. MDS-A(config)# role name sangroup MDS-A(config-role)# vsan policy deny MDS-A(config-role-vsan)# permit vsan 500

Refer to the exhibit.

Which command is used to determine which switch has the lock?

A. show fcs ie vsan

B. show zoneset active

C. show zone status

D. show flogi database

Which command identifies the application and the user that have a Cisco Fabric Services session open?

A. show cfs application

B. show zoneset active

C. show cfs lock D. show device-alias database

Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?

A. The autoreconfigure option is disabled on both switches.

B. The autoreconfigure option is enabled on both switches.

C. The rcf-reject option is enabled on the interfaces.

D. The rcf-reject option is disabled on the interfaces.