1Z0-1075-20 Online Practice Questions and Answers

Your customer plans to use Oracle Representational State Transfer (REST) API with Oracle Supply Chain Management Cloud (Oracle SCM Cloud) to support integration requirements. Identify four REST resources and the corresponding HTTP action available with Manufacturing Cloud.

A. Work Order Status GET method

B. Work Orders GET method

C. Work Order Status POST method

D. Work Orders PATCH method

E. Resource transaction POST method

F. Resource transaction GET method

In a manufacturing plant, the work definition and rate plans of Material, Resource, and Overhead of an assembly have been defined as required. A cost accountant created different scenarios to represent different manufacturing and cost assumptions and compare the results. When the cost assumptions are finalized, the cost accountant is expected to publish the cost scenario to cost accounting. Identify three process steps that the cost accountant has to perform to transfer the assembly to cost accounting in frozen type.

A. Publish cost planning scenario to Accounting.

B. Build cost planning scenario and perform cost roll up.

C. Create Accounting Distributions.

D. Transfer transactions from production to Costing.

E. Define a cost planning scenario with Material, Resource, Overhead cost plans, and work definition.

F. Transfer Transactions from Inventory to Costing.

A plant runs 24x7 daily using three continuous shifts of 8 hours each. One unit of an equipment resource R1 is assigned to each of the three shifts. On a specific work order, the resource R1 is required to work for 2 hours. The resource is set up with an efficiency of 50% and utilization of 100%. R1 is scheduled to start on the given work order at noon. What time will R1 be scheduled to finish, assuming no calendar exceptions have been set?

A. 8:00 PM

B. 12:30 PM

C. 2:00 PM

D. 4:00 PM

E. 1:00 PM

An order entry specialist creates a Back-to-Back order for product item with an intention of fulfilling by in-

house manufacturing. The fulfillment line is scheduled and Supply Chain Orchestration (SCO) has initiated

creation of a Supply Order rather than Work Order.

Identify two options that can cause this situation.

A. Sourcing rules for the product item are defined as Make as well as Transfer.

B. Sourcing rule for the product item is defined as Make, but Work Definition is not defined.

C. Sourcing rules for the product item are defined as Buy as well as Transfer.

D. Sourcing rule for the product item is defined as Buy.

A production Supervisor has noticed that Work Orders created manually are overwritten by the plan runs

executed by Planning Central. After discussing this issue with the Planner, two actions are recommended

to prevent the Work Orders from being overwritten by plan runs.

Identify the two recommendations.

A. Update Supply Plan Options, Overwrite Firm Planned Orders = None.

B. Update Firm flag in the Details region of the Edit Work Definition page.

C. Update Firm flag in the Details region of the Edit Work Definition Names page.

D. Update Firm flag in the Details region of the Edit Work Order page.

A production operator needs to review the materials issued, resources charged, and operations performed for a job that was executed in the previous shift. Identify the task the operator has to select to review all the transactions in a single place for both Work Order and Orderless execution.

A. Manage Work Orders

B. Review Dispatch List

C. Report Resource, Material and Operation Transactions

D. Review Production Transaction History

Identify four parameters that are considered in the calculation of manufacturing lead time in Oracle Manufacturing Cloud.

A. Resource calendars of the work centers involved

B. The primary work definition of the item

C. The lot size of the item

D. The shifts are defined in the plant calendar

E. Plant calendar exceptions

F. Resource calendar exceptions

Your Customer has implemented Oracle Cloud Manufacturing and the Manufacturing user is in the

process of defining Work Definition and Operations. However, this user is unable to assign an ad hoc item,

Grease, to an operation.

Identify the reason.

A. The user doesn't have Override Item Structure Components in the Work Definition privileges.

B. An item cannot be assigned on an ad hoc basis.

C. The user doesn't have access to the PIM module.

D. The user doesn't have Data access to create item structure.

You are setting up Fusion Manufacturing to support Back-to-Back Fulfillment. Identify an option that needs to be set for oracle Fusion Planning Central to plan back-to-back item components and resources.

A. Select the Used in Planning check box in the new Work Definition.

B. Select the Used in Planning check box in the Work Definition Names.

C. Select the Used in Planning check box in the Work Structure.

D. Select the Used in Planning check box in the item definition.

You want to use a predefined Standard Operation in a Work Definition, but you also want to change the usage of the Standard Operation resource. Identify the setup required.

A. Deselect the Referenced check box while adding the standard operation to the work definition and change the usage manually.

B. Select the Referenced check box while adding the standard operation to the work definition and change the usage manually.

C. Use the Transfer and Edit Standard Operation functionality to edit the resource usage.

D. Use a Resource exception for the resource and alter its usage.

Your customer runs two daily shifts in her plant: Morning Shift and Evening Shift. A resource LATHE is assigned to the work center W1. There are five units of LATHE available, of which three units are available for the Morning Shift and the remaining units are available for the Evening Shits. Which two actions must you perform to associate LATHE with W1?

A. Do not select the Available 24 Hours check box and in the Resource Availability region, enter 3 against the resource LATHE in the Morning Shift column.

B. Select the Available 24 Hours check box and in the Resource Availability region, enter 3 against the resource LATHE in the Morning Shift column.

C. Select the Available 24 Hours check box and in the Resource Availability region, enter 2 against the resource LATHE in the Evening Shift column.

D. Do not select the Available 24 Hours check box and in the Resource Availability region, enter 2 against the resource LATHE in the Evening Shift column.

E. Do not select the Available 24 Hours check box and in the Resource Availability region, enter 60% against the resource LATHE in the Morning Shift column.

F. Do not select the Available 24 Hours check box and in the Resource Availability region, enter 40% against the resource LATHE in the Evening Shift column.

You are in the process of defining a Standard Operation for visual inspection. You want the completion of this standard operation to be reported in all work orders that reference it. Identify the setup that will fulfill this requirement.

A. Select the Automatically Transact check box while defining the Standard Operation.

B. Deselect the Count Point check box while defining the Standard Operation.

C. Select the Count Point check box while defining the Standard Operation.

D. Ensure that the Charge Type of the resource is Automatic.

The Cost Accountant has reported to the Production Supervisor that the Work Order transactions are not

getting transferred to Costing.

Identify the reason for work order transactions not getting transferred to Costing.

A. The Manage Item Rules setup is not complete.

B. The Costing Interfaced Attribute is enabled in the resource definition.

C. The item was made inactive after the Work Order transaction.

D. The Costing Interfaced Attribute is not enabled in the resource definition.

As part of an implementation project, you have to perform setups related to a Manufacturing plant in Functional Setup Manager.

What must be set up first in order for you to configure the setup task called Manage Plant Parameters?

A. The Supply Chain Orchestration Functional Area

B. The Manufacturing Master Data Functional Area

C. The Manage Items Profile Options tasks

D. The Manage product and Child Value Sets task

The production user wants to report Work Order completion. Identify two ways of reporting the progress of work order at work order operation level.

A. Change Move status to Ready.

B. Complete using quantity completion

C. Complete with Details

D. Quick Complete

E. Change status of Operation to completed